P550 掉电,系统启动后黄灯消除问题
今天机房掉了两次电.致P550(AIX5.3)启动后亮黄灯,用diag运行报以下错误:
The path between the following resources is missing:
U787B.001.DNW4387-
hdisk5 P1-T14-L8-L0 16 Bit LVD SCSI Disk Drive (73400 MB)
U787B.001.DNW4387-
scsi0 P1-T14 PCI-X Dual Channel Ultra320 SCSI Adapter
bus
Select an option to resolve the missing path.
Continue to run diagnostics on the selected resource.
This selection will leave the path in the system configuration.
The path has been removed.
This selection will remove the path from the system configuration.
The path has not been removed.
This selection will determine why the path is shown as missing.
各位帮忙看看是不是硬盘有问题了,有什么解决办法?先谢了
[ 本帖最后由 cn_compass 于 2009-4-21 15:59 编辑 ]
The path between the following resources is missing:
U787B.001.DNW4387-
hdisk5 P1-T14-L8-L0 16 Bit LVD SCSI Disk Drive (73400 MB)
U787B.001.DNW4387-
scsi0 P1-T14 PCI-X Dual Channel Ultra320 SCSI Adapter
bus
Select an option to resolve the missing path.
Continue to run diagnostics on the selected resource.
This selection will leave the path in the system configuration.
The path has been removed.
This selection will remove the path from the system configuration.
The path has not been removed.
This selection will determine why the path is shown as missing.
各位帮忙看看是不是硬盘有问题了,有什么解决办法?先谢了
[ 本帖最后由 cn_compass 于 2009-4-21 15:59 编辑 ]
38 同行回答
机房突然断电后 等机器起来亮黄灯 首先应该进asm看event log 如果系统可以进去可以查errpt 看是否和asm里面的报错对的上号 确认没啥大问题后再消黄灯 消黄灯得方法多了去了 没分区的可以在diag里这么做。。。。 收起
在HMC上通过菜单项选择也可以去掉。 收起
还有别的办法吗？ 收起
原帖由 lwb_aix 于 2009-4-21 16:15 发表 如何哥们？解决什么问题了？
机房断电了两次(晕啊.),系统启动后出现黄灯原帖由 lbclcy 于 2009-4-21 16:17 发表
当时IBM给我们的方法就是下面这些，我们的小机是P.3的所以你看看能不能帮你，希望你也能好转~！！！
IBM小型机
重置告警灯状态
1、使用root用户登陆系统，执行“diag”命令，回车继续；
2、看到“Press the F3 key to exit or pre ...
好的,谢谢.我刚才试了:
Continue to run diagnostics on the selected resource.
This selection will leave the path in the system configuration.
现在黄灯没了,现在还不能确定过段时间会不会再显示 收起
我早上用:
1、Root用户执行diag；
2、回车后，进第3项，Task Selection (Diagnostics, Advanced Diagnostics, Service Aids, etc.)；
3、选Identify and Attention Indicators;
4、Set ALL Identify Indicators to NORMAL,回车;
当时黄灯是没了,可下午又亮了. 收起
1、Root用户执行diag；
2、回车后，进第3项，Task Selection (Diagnostics, Advanced Diagnostics, Service Aids, etc.)；
3、选Identify and Attention Indicators;
4、Set ALL Identify Indicators to NORMAL,回车;
当时黄灯是没了,可下午又亮了. 收起