HACMP资源组error

小型机安装配置完全手册收起

小型机安装配置完全手册收起

COMMAND STATUS

Command: OK            stdout: yes           stderr: no

Before command completion, additional instructions may appear below.

[TOP]

Verification to be performed on the following:
        Cluster Topology
        Cluster Resources

Retrieving data from available cluster nodes.  This could take a few minutes.
        
        Start data collection on node node1
        Start data collection on node node2
        Collector on node node2 completed
        Collector on node node1 completed
        Data collection complete
WARNING: Cluster verification detected that some cluster components are
inactive. Please use the matrix below to verify the status of
inactive components:
Node: node1
  Resource Group: heartrg                                State: ERROR
Node: node2
  Resource Group: racrg                                  State: ERROR

Verifying Cluster Topology...
        
        Completed 10 percent of the verification checks
        Completed 20 percent of the verification checks
WARNING: Node node1: Read on disk /dev/hdisk6 failed.
  Check cables and connections.
  A reserve may be set on that disk by another node.

WARNING: Node node1: Read on disk /dev/hdisk7 failed.
  Check cables and connections.
  A reserve may be set on that disk by another node.
WARNING: Multiple communication interfaces are recommended for networks that
use IP aliasing in order to prevent the communication interface from
becoming a single point of failure. There are fewer than the recommended
number of communication interfaces defined on the following node(s) for
the given network(s):

    Node:                                Network:
    ----------------------------------   ----------------------------------
    node1                                net_ether_01
    node2                                net_ether_01
   
WARNING: The RSCT level is inconsistent in the cluster:


node1   AIX 6.1.0.0
        rsct.core.utils    3.1.2.1
        rsct.basic.hacmp   3.1.2.0
        rsct.basic.rte     3.1.2.1
        rsct.core.sec      3.1.2.0
        
node2   AIX 6.1.0.0
        rsct.core.utils    3.1.2.0
        rsct.basic.hacmp   3.1.2.0
        rsct.basic.rte     3.1.2.0
        rsct.core.sec      3.1.2.0
        
    To ensure HACMP is working properly, it is recommended
that the same level of RSCT software be installed on nodes
with the same level of AIX.

        Completed 30 percent of the verification checks
        
        
        
        Completed 40 percent of the verification checks
Verifying Cluster Resources...

        Completed 50 percent of the verification checks
        Completed 60 percent of the verification checks
        Completed 70 percent of the verification checks
        Completed 80 percent of the verification checks
        Completed 90 percent of the verification checks
        Completed 100 percent of the verification checks
        
Remember to redo automatic error notification if configuration has changed.

Verifying additional pre-requisites for Dynamic Reconfiguration...
...completed.

Committing any changes, as required, to all available nodes...
Adding any necessary HACMP entries to /etc/inittab and /etc/rc.net for IPAT on node node1.
Adding any necessary HACMP entries to /etc/inittab and /etc/rc.net for IPAT on node node2.

Verification has completed normally.

cldare: No changes detected in Cluster Topology or Resources.
...completed.

Committing any changes, as required, to all available nodes...
Adding any necessary HACMP entries to /etc/inittab and /etc/rc.net for IPAT on node node1.
Adding any necessary HACMP entries to /etc/inittab and /etc/rc.net for IPAT on node node2.

Verification has completed normally.

clsnapshot: Creating file /usr/es/sbin/cluster/snapshots/active.0.odm...

clsnapshot: Succeeded creating Cluster Snapshot: active.0.

cldare: Requesting a refresh of the Cluster Manager...
...completed.


[BOTTOM]

F1=Help                                   F2=Refresh                                F3=Cancel                                 Esc+6=Command
Esc+8=Image                               Esc+9=Shell                               Esc+0=Exit                                /=Find
n=Find Next

已经同步过了收起

做个同步再看下收起