DataDomain 备份设备安装配置维护文档
目 录
3. 附加配置( szDD510 和 bjDD510 都需要配置) ... 10
**# 一、说明
以下为安装信息及安装过程。安装信息,例如主机名、 IP 地址等,需要用户方提供后修改,安装过程基本一致,某些信息在安装过程中将与用户讨论,安装结束后提供安装文档的最终版本。、
安装前提及进度过程:
软件名 | Symantec NetBackup |
版本 | 6.5 |
备注 |
主机名 | IP | OS | 说明 |
igwbkoa | 10.86.228.64 | Windows Server 2003 | Master Server/ Media Server |
igwbkdealing | 10.86.192.64 | Windows Server 2003 | Master Server/ Media Server |
设备型号 | DD510 | DD510 |
主机名 | szDD510 | bjDD510 |
IP | 10.86.228.67 | 10.86.10.20 |
Netmask | 255.255.255.0 | 255.255.255.0 |
Gateway | 10.86.228.253 | 10.86.10.252 |
DNS Domain Name | localdomain | localdomain |
DNS Server | ||
Admin email | zhouxc@invescogreatwall.com | |
Other alert email | ||
SMTP server | 10.86.228.45 | |
备份连接方式(FC/LAN) | LAN | LAN |
设备型号 | 功能 | 备注 |
**# 三、安装及配置
1.1 szDD510 上机架( DD510 是 3U 的设备)
1.2 szDD510 通过 eth0,eht1 两个网口直连到 OA 和 dealing 两台备份服务器, eth3 连接到本地网络交换机(和北京相通)
1.3 bjDD510 连接到网络交换机(和深圳相通)
1.4 连接主机三个电源
连接 RS232 线到一台电脑,打开终端程序(如“超级终端”),按 DD510 电源开关开机。
根据配置提示输入信息(也可以以后再配置)
(冒号后面为输入值)
Data Domain OS 4.6.1.0-88314
localhost.localdomain login: sysadmin
Password:
Welcome to Data Domain OS 4.6.1.0-88314
sysadmin@szDD510# config setup
Licenses Configuration
Configure Licenses at this time (yes|no) [no]:
Network Configuration
Configure Network at this time (yes|no) [no]: yes
Hostname
Enter the hostname for this system (fully-qualified domain name)
[szDD510.localdomain]:
Domainname
Enter your DNS domainname
[localdomain]:
Ethernet port eth0
Enable Ethernet port eth0 (yes|no|?) [yes]:
Use DHCP on Ethernet port eth0 (yes|no|?) [no]:
Enter the IP address for eth0
[192.168.14.3]:
Enter the netmask for eth0
[255.255.255.0]:
Ethernet port eth1
Enable Ethernet port eth1 (yes|no|?) [yes]:
Use DHCP on Ethernet port eth1 (yes|no|?) [no]:
Enter the IP address for eth1
[192.168.14.4]:
Enter the netmask for eth1
[255.255.255.0]:
Ethernet port eth2
Enable Ethernet port eth2 (yes|no|?) [no]:
Ethernet port eth3
Enable Ethernet port eth3 (yes|no|?) [yes]:
Use DHCP on Ethernet port eth3 (yes|no|?) [no]:
Enter the IP address for eth3
[10.86.228.67]:
Enter the netmask for eth3
[255.255.255.0]:
Default Gateway
Enter the default gateway IP address
[10.86.228.253]:
DNS Servers
Enter the DNS Server list (zero, one, two or three IP addresses)
:
Pending Network Settings
Hostname szDD510.localdomain
Domain name localdomain
Default Gateway 10.86.228.253
DNS Server List DNS Server List
Port Enabled Cable DHCP IP Address Netmask
eth0 yes yes no 192.168.14.3 255.255.255.0
eth1 yes yes no 192.168.14.4 255.255.255.0
eth2 no no n/a n/a n/a
eth3 yes yes no 10.86.228.67 255.255.255.0
Do you want to save these settings (Save|Cancel|Retry): S
Filesystem Configuration
Configure Filesystem at this time (yes|no) [no]: yes
Global compression type
Will this restorer replicate to/from restorers with the old global compr
ession type "1"? (yes|no|?) [no]:
Local compression type
What local compression type will this filesystem use? (none|lz|gz|gzfast
) [lz]: [lz]:
Marker type
What marker type will this filesystem use? (none|nw1|cv1|tsm1|tsm2|eti1|hpdp1|besr1|ssrt1|is
m1|auto) [auto]:
Pending Filesystem Settings
Global Compression Type 9 (no change)
Local Compression Type lz
Marker type auto
Do you want to save these settings (Save|Cancel|Retry): S
System Configuration
Configure System at this time (yes|no) [no]: yes
Admin Host
Enter a hostname for administrative access to the restorer
[all]:
Admin Email
Enter an email address or group alias that will receive email
from the restorer. The address is also used as the 'From'
address in all email sent by the restorer.
[zhouxc@invescogreatwall.com]:
System Location
Enter a physical location, to better identify this system.
[SZ]:
Mail Server
Enter the hostname of a mail (SMTP) server to relay email alerts.
[10.86.228.45]:
Timezone
Enter your timezone name.
[Asia/Shanghai]:
Configure NTP
Enable Network Time Service? (yes|no) [yes]:
Use multicast for NTP? (yes|no) [no]:
Enter the NTP Server list
[10.86.228.69]:
Pending System Settings
Admin host all
Admin email zhouxc@invescogreatwall.com
System location SZ
SMTP server 10.86.228.45
Timezone Asia/Shanghai
NTP Servers 10.86.228.69
Do you want to save these settings (Save|Cancel|Retry): S
CIFS Configuration
Configure CIFS at this time (yes|no) [no]:
NFS Configuration
Configure NFS at this time (yes|no) [no]:
System Configuration
Configure System at this time (yes|no) [no]:
Configuration complete.
添加主机解析
sysadmin@ # net hosts add 10.86.228.67 szDD510
sysadmin@ # net hosts add 10.86.10.20 bjDD510
添加管理员邮件
sysadmin@ #autosupport add zhouxc@invescogreatwall.com
添加远程管理
打开 ssh 访问:
sysadmin@# adminaccess enable ssh
打开 http 访问
sysadmin@# adminaccess enable http
添加 cifs 配置
sysadmin@ # cifs add /backup all
在运行菜单里键入“ \\ ”查看可以正常访问共享目录
1 )分别在 szDD510 和 bjDD510 上 backup 目录下建立 igwbkdealing 目录
2 )分别在 szDD510 和 bjDD510 上执行以下命令,建立复制对:
3 )在 szDD510 上执行以下命令,初始化复制对:
sysadmin@szDD510# system show hardware
Slot Vendor Device Ports
0 Intel 80003ES2LAN GigE 0a, 0b
1 Micro Memory MM-5425CN
2 (empty) (empty)
3 (empty) (empty)
4 (empty) (empty)
5 Intel PRO/1000 PT DP GigE 5a, 5b
6 (empty) (empty)
sysadmin@szDD510# system show modelno
Model number: DD510
sysadmin@szDD510# system show serialno
Serial number: 8F45133036
sysadmin@szDD510# system show version
Data Domain OS 4.6.1.0-88314
sysadmin@szDD510# net show hardware
Port Speed Duplex Supp Speeds Hardware Address Physical Cable
eth0 1000Mb/s full 10/100/1000 00:15:17:65:2c:14 Copper yes
eth1 1000Mb/s full 10/100/1000 00:15:17:65:2c:15 Copper yes
eth2 unknown unknown 10/100/1000 00:15:17:aa:2d:0e Copper no
eth3 1000Mb/s full 10/100/1000 00:15:17:aa:2d:0f Copper yes
sysadmin@szDD510# cif show clients
path client
/backup all
sysadmin@szDD510# user show list
User list from node "localhost".
Name Uid Class Last Login From Last Login Time
sysadmin 100 admin never
administrator 500 user never
2 users found
用户名 / 口令: sysadmin / sysadmin
ssh 10.86.228.67
用户名 / 口令: sysadmin / sysadmin
在机房的 KVM 上可以直接操作 DD510 。用户名 / 口令: sysadmin / sysadmin
其它方式都不能操作的情况下,也可以使用串口进行操作。
用户名 / 口令: sysadmin / sysadmin
按 DD510 正面的开关按键(将面板拔出可看到开关)。
关机步骤:
1) 在备份服务器上确认没有备份或恢复任务运行
2) 用 ssh 或 console 登录到 DD510 中
3) 输入 system poweroff , dd510 会执行正常关机步骤,并自动关闭电源
登录后:
登录 Web 界面,点选 Replication
如果觉得我的文章对您有用,请点赞。您的支持将鼓励我继续创作!
赞3
添加新评论0 条评论